🇬🇧

Know How

Eurocode#

Eurocodes in event technology#

The Eurocodes are a series of standards for structural design. Eurocode 0 covers the basis of structural design and the safety concept, Eurocode 1 covers actions, and Eurocodes 2 through 9 contain material-specific design rules.

Important: This overview explains terms; it does not replace a complete design or the assessment of a specific structure. Which rules apply depends, among other things, on the location, the structure, its use, and the applicable editions of the standards and National Annexes. Have the applicable requirements and results reviewed by a suitably qualified person. A result from Production Assist alone does not authorize construction.

The German Social Accident Insurance (DGUV) publishes Regulation 17 and the related Rule 115-002 for event and production venues. DGUV Information 215-313 on loads above people provides additional guidance. Read these publications in their applicable context; they do not establish a blanket rule that every structure must be verified solely according to a particular Eurocode.

DIN Media marks the previous edition DIN 56950-1:2012-05 as withdrawn and lists DIN EN 17206:2022-02 as its successor. For a specific design, always check the current edition of the standard and its scope directly with the standards publisher DIN Media; the overview below is no substitute for doing so.

Overview#

The Eurocodes are a European system for structural design. The following names describe the subject areas of the standards; they do not replace checking the current edition and the applicable National Annex.

  • Eurocode 0: Basis of structural design (EN 1990)
  • Eurocode 1: Actions on structures (EN 1991)
  • Eurocode 2: Design of concrete and prestressed concrete structures (EN 1992)
  • Eurocode 3: Design of steel structures (EN 1993)
  • Eurocode 4: Design of composite steel and concrete structures (EN 1994)
  • Eurocode 5: Design of timber structures (EN 1995)
  • Eurocode 6: Design of masonry structures (EN 1996)
  • Eurocode 7: Geotechnical design (EN 1997)
  • Eurocode 8: Design of structures for earthquake resistance (EN 1998)
  • Eurocode 9: Design of aluminium structures (EN 1999)

The safety concept distinguishes between actions and resistances. The values and partial safety factors to be used depend on the applicable edition of the standard, the National Annex, and the specific design case. Safety factors apply on both the action side and the resistance side.

Actions are all effects acting on the structure. A force or an imperfection is an example of an action. Resistances oppose the actions and are determined by the cross-sectional and material properties.

Partial safety factors account, among other things, for uncertainties in actions and resistances. Do not use general values from an overview as project requirements.

Actions are first determined for the structure. Verifying resistances also depends on the material, cross-section, connections, and applicable design rules.

Eurocode 0#

Classification of actions#

A structural calculation considers a particular load and operating condition. Dynamic effects such as acceleration, braking, and swinging must be taken into account when they are relevant to the specific use.

Derive the necessary load assumptions and combinations from the specific use and applicable rules. The Production Assist factor Load factor for all loads multiplies the modelled loads; it does not replace a technical determination of dynamic actions.

Dynamic effects occur in particular when truss systems are moved by motors at high speeds and accelerations.

Each load is classified by its type as either a permanent or a variable action.

Permanent actionsVariable actions
ClassificationThe loads are continuously present during the service life of the structureThe loads are not continuously present during the service life of the structure
SymbolGkQk
ExamplesDead weight, earth loads, ground movementsImposed loads, snow loads, ice loads, wind loads, temperature variations
Partial safety factorAssess whether the effect of each permanent action is favourable or unfavourable.Assess whether the effect of each variable action is favourable or unfavourable.

Whether an action has a favourable or unfavourable effect depends on its effect on the verification being considered. The table provides a qualitative classification; it is not instructions for entering factors.

Determine factors and combinations for each limit state from the applicable rules. The supplied Production Assist load combinations and their factors can vary depending on the project template. Check and document the combination used in the instructions for load combinations.

Design objectives#

Structural design distinguishes, among other things, between two design objectives:

  • Load-bearing capacity
  • Serviceability
Load-bearing capacityServiceability
Design objectiveSafety of functions
Safety of the structure
Function of the structure
User well-being
Appearance of the structure
AssessmentLoss of positional stability
Failure due to excessive deformation
Transition of the structure into a kinematic state
Breakage
Unstable position
Deformations
Vibrations
Damage
DescriptionThe load-bearing capacity verification is intended to rule out failure of the structure. It is therefore a “hard” criterion that protects not only the structure but, in particular, people below it.Serviceability supports user well-being and ensures functionality. It is therefore more of a “soft” criterion. Consider whether users will feel safe beneath strongly bent or vibrating structures, even if they may not fail. A deformed structure can also impair functions, for example in rail systems.
VerificationLoad-bearing capacity is assessed using the resistances and verifications relevant to the specific structure. Which components, connections, and limit states must be checked depends on the system and the applicable rules.Serviceability concerns, for example, deformations and vibrations. Limits must come from the applicable standard, project specification, or manufacturer's information; there is no universally applicable deflection limit.

Depending on the model, Production Assist can calculate loads, reactions, deformations, and cross-section utilization. Check the calculation scope and settings used; the integrated calculation does not replace a complete external assessment. See Structural calculation.